close

Plumbing

Plumbing

How To Stop A Ball Faucet From Dripping?

b_sand-wall-mounted-kitchen-mixer-tap-carlo-nobili-rubinetterie-285243-reld62e89a1

A ball faucet is a common type of faucet used in kitchen sinks. It is single-lever, usually with a narrow body and a crank that allows smooth movement in all directions. Inside her body is a plastic or metal sphere that controls the flow of water. Leaks in this type of faucet usually occur when the outside becomes loose or when the inner rings or meet our team.

Circle or rubber valve wears out. The ball is rarely the cause of the leak, but you can replace it if it is visibly damaged.

Step 1

Tighten the outside of the faucet, if applicable, using channel pliers. Wrap the plier’s teeth with tape to avoid scratching. A loose faucet can result in a leak. If the leak. Don’t stop; proceed to the next step.

Step 2

Stop water access to the faucet by closing the valve under the sink. Loosen or remove the adjustment screw or fastener securing the handle to the faucet body and using an Allen wrench or other tool. Proper. Pull off the handle and set it aside.

Step 3

Release the outside and remove it from the faucet body. Pay attention to the direction and location of each internal part of the faucet body before removing them; this is necessary to later assemble it back with the pieces.

In the right places. Take out the plastic and rubber chamber and remove the ball. Check if it is damaged. Carefully remove the two valves and springs using a small screwdriver.

Step 4

Pull the spout off the faucet body and remove the “O” rings around the outside of the body.

Step 5

Purchase a faucet repair kit with new “O” rings, new valves and springs, as well as other rubber tubes; bring the old faucet parts to the store to buy identical parts.

Step 6

Apply waterproof and temperature-proof grease to the rings and place them in place on the faucet body. Reassemble the faucet using the new parts. Slowly open the water valves and test the faucet.

How To Fix A Leaky Faucet In 6 Simple Steps?

For the water consumption to be as little as possible, periodic maintenance on your faucets should be carried out. Repairing a leaky faucet is a very common problem, but after reading ours. Step-by-step, you will find that it is also a very easy problem to solve. It doesn’t matter if your faucet has separate handles for hot and cold water or just one for both, every faucet. It works according to some basic principles. See in 6 steps how simple it is to fix your leaky faucet and never waste water again.

Shut Off The Water Supply

Shut off the water supply and remove the faucet handle by loosening the small screw at the top or back of the handle. Once you remove the cover, you will see the screw installed in part. Top of the handle. If necessary, use penetrating oil to help disassemble it.

Remove The Packing Nut

Carefully remove the packing nut with good-sized pliers or adjustable wrench to not leave marks on the metal. Twist the stem or spindle by turning it in the same direction as you would turn on the faucet.

Remove The Screw That Holds The Seal.

Remove the screw holding the seal. If necessary, use penetrating oil to loosen the bolt. Check bolt and stem, and replace if damaged.

Replace Old Seal

Replace the old seal with a new one. Some seals will work for both, but you must be sure to purchase the exact replacement parts.

Fit The New Washer

Fit the new sealing washer onto the stem and reinstall the assembly into the faucet. Rotate the rod clockwise.

Release The Water Supply

Replace the handle and screw cap. Release the water supply and check if leaks continue.

Ready!

Water leaks can cost a fortune. Needlessly, just one drop per second wastes about ten thousand liters of water a year. Most leaks are easy to fix. Try to visit the website. There is no point in keeping the waste since repairing a faucet costs very little to the cost generated by wasting water.

read more
Plumbing

How to Maintain Your Drains to Prevent Blockages

Paste (6)

Drains are important features every home must have.  Without it, the sanitation and health of the people inside will be compromised. The water supply system surrounding a property with a poor drainage system is also put at risk and becomes compromised.

While most minor clogs can be easily washed away with basic household cleaning tools, frequent clogging in your drains are indicators that a major clog has already developed in your drain line. Major clogs can form in a span of a month, some years, due to accumulation of different foreign materials in your drains, which should have been pushed down the drain.

To avoid major clogs and blockages from forming down your drain, maintaining a clean and efficient drainage system is a must. Although there are plenty of blocked drain repair Sydney plumbers available to help you repair and address drain issues, preventive maintenance and discipline at home can save you hundreds of dollars from unnecessary drain repairs and replacement services.

Here are some effective, yet very basic tips that can help prevent clogs in your drains and keep them in good working condition.

Practice Proper Waste Disposal

What you throw down the drain accumulates and creates your future plumbing problems. Leftover food, coffee grounds and grease from kitchen drains can stick and last in your pipes for a long time. As much as possible, throw all your leftover food in the thrash or compost, instead of your garbage disposal.

The same is true with leftover liquid grease and cooling oil. Place them in a sealable container and throw them together into the thrash. If recycling centres are available in your area, you can bring your used oils to them to recycle.

Hair and soap scum is the equivalent of food leftover and grease for your kitchens, this time, in the bathroom area.  Covering your tubs and shower drains with a mesh screen or a drain cover can do a lot of wonders in capturing hair and soap scum, preventing them from going down the drain.

Lastly, be mindful of what you flush down your toilet. Although some toilet paper is designed to be flushed, it is still best to dispose of all your toiletries in a trash can, rather than letting them go down the drain. Flushing dense materials can cause severe clogs and other plumbing issues in your drains.

Keep Your Drains Clean

Cleaning your drains weekly is a good practice to keep them working in top condition. Interestingly, you can clean your drains without the help of a professional.

For bathroom sinks, you can simply pull out the pop-up stopper in your bathroom sink to remove any debris that may have passed down your drain stoppers. You can use a bent wire to fish out hair and other debris from your pipes.

Flushing your drains weekly with hot water is also a good practice. You can even pour baking soda and vinegar mixture to be able to break down possible clogging or blocks that may have already built up inside your drains.

Deep cleaning your drains at least once a month is also a good practice. Remove the pop-up assembly and the overflow plate to give your drains a good scrubbing. You can also use bacterial drain cleaners, at least once a month or every two months to keep mould and bacteria build up away from your drain system.

Lastly, regular maintenance checks from your local plumber in Sydney at least once or twice a year can give you enough confidence that your drains are working in top condition. Professional plumbers can spot plumbing and drain issues that you may have been failing to notice. This gives them an opportunity to address these issues, at its earlier stages, decreasing the amount of stress and expenses that comes with severe damage and poorly working drainage systems.

read more